Mackie RTA-31 Betriebsanweisung

USER’S GUIDERTA-31™™®Plug-in for Mackie Digital Mixers™

10Acuma RTA-31Assigning an Input SourceIn the INPUT column of the Plugin Configuration screen, select aninput source for the RTA-31. This can be an au

User’s Guide11Using the RTA-31Front Panel (Overview)You can think of the RTA-31 as being comprised of two separatepanels: the EQ Panel and the Analyze

12Acuma RTA-31Mouse ControlUse your mouse to perform various editing EQ functions:• Single Set: Click the left mouse button to adjustindividual bands

User’s Guide13The Main Control BarEQThe EQ selection button toggles the graphic EQ in and out ofview via the mouse. Clicking the EQ button when the an

14Acuma RTA-31EnableThis button simply enables or disables the RTA-31 for a wet/drycomparison.Preset Toggle ButtonsThe up/down arrows, located just to

User’s Guide15The Analyzer PanelThe Analyzer WindowThe analyzer window is represented by thirty-one bar graphsthat correspond to the same thirty-one s

16Acuma RTA-31Graph Speed SelectGraph speed select refers to the response speed of the Analyzermeters. It controls the peak and hold times as well as

User’s Guide17The Reduced Screen Control BarThe Reduced Screen Control BarThe control bar is a convenient way of viewing your signalwithout taking up

18Acuma RTA-31Saving, Loading and Resetting a PresetRTA-31 settings can be saved andrecalled from the hard drive. You cansave and load files to either

User’s Guide19To Load a Preset:1. Click MEM A or MEM B tochoose the memory locationfrom which to load the file.2. Click and hold the MENU button.3.

2Acuma RTA-31Iconography“Mackie” and the “Running Man” figure are trademarks orregistered trademarks of Mackie Designs Inc. All other brandnames menti

20Acuma RTA-31To Reset The Preset:Reset will reload the previous patch.1. Click and hold the MENUbutton.2. Select Reset Graphic EQ.To Cut Preset Set

User’s Guide21Dynamic Real TimeTo Write Automation on a Loaded Plug-In:1. Engage AUTO TOUCH.2. Engage ALL, disengageBYPASS, and sendtimecode to the

22Acuma RTA-31FX RoutingThe Plugin Configuration WindowCard Slot ColumnCard BCard CCard DCard APlug-indisplay toggleInput ChannelAssignment Pull-down

User’s Guide23Inserting a Plug-in into a ChannelA pre- or post-DSP channel insert can also be used as the inputsource for a plug-in. When a channel in

24Acuma RTA-31Using an Aux Send with a Plug-In♦ Click on the associated INPUT menu button and selectan Aux input source. In the example below, we ha

User’s Guide25You will see the plug-in’s input meter become active as you raisethe mixer input channel’s aux send.Set the plug-in input/output signal

26Acuma RTA-31The FX Return Channel♦ Switch the D8B Bank Select toEFFECTS (49-72) and bring upfaders one and two (channels 49 and50). You will also

User’s Guide27Factory PresetsThe following table is a simple guideline to help you understandthe factory presets, and which type of source file was ap

©2001 Mackie Designs Inc. and Acuma Labs. All Rights Reserved.Part No. 820-257-00 Rev. A1 07/2001™®

User’s Guide3ContentsIconography ----------------------------------------------------- 2Introduction ----------------------------------------5About Ac

4Acuma RTA-31Preset Title Window ------------------------------------------14 Input Select ----------------------------------------------------14The C

User’s Guide5IntroductionThank you for purchasing the RTA-31, the ultimate inequalization and frequency analysis from Acuma Labs. It is oneof the exci

6Acuma RTA-31About the RTA-31Acuma Labs' RTA-31 is a dedicated software plug-in for theMackie Digital 8•Bus that utilizes 24-bit digital processi

User’s Guide7Requirements• One or more Mackie UFX cards• Mackie Real Time OS 3.0 Software• Plug-in SoftwareWe will assume you have successfully ins

8Acuma RTA-31Unlock Procedure1. Locate your D8B’s Electronic Serial Number (ESN). Thisis displayed at the bottom of the Licensing window,which is acc

User’s Guide9Configuring the Plug-InAfter installing your UFX card, unlocking the plug-in, andbooting up the D8B, all you need to do is assign the RTA