Mackie M800 Bedienungsanleitung PDF herunterladen (Seite 12)

POWER CORD

The M•800 is supplied with a detachable

power cord. Make sure the power switch is off

before firmly attaching the cord to the ampli-

fier. Fit the other end into an AC outlet

properly configured for the type of plug on the

power cord and for the voltage rating of the

amplifier.

For current-delivery purposes, the M•800’s

voltage source (wall outlet, extension cords, or

power strips) must be capable of continuously

delivering 12 amps (US model). And for safety

reasons, that source must be a “3-prong” outlet

with hot, neutral, and ground terminals. We’re

dealing with some big-time electricity here —

don’t mess with it. See “AC Power Consider-

ations” on page 18.

SPEAKER OUTPUTS

To use the binding post outputs, you can

terminate your speaker cables with single or

dual banana plugs, or bare wire.

To use banana plugs:

First pull off the small

plastic end caps from

each of the binding posts

to reveal the holes. It is

important to hand-

tighten each post before

plugging in the bananas.

To use bare wire:

Unscrew the amp’s bind-

ing posts, insert your

stripped wires (stripped

about 3/8" back) into the

side holes and retighten

the posts (finger tight is fine — do not use a

wrench!). Be careful that no wire strands

touch the chassis or other terminals.

The red posts are labeled “+,” which means

positive, and the black posts are labeled “–” for

negative. The amplifier is “common grounded,”

that is, both black posts are connected inter-

nally to ground.

Use high-quality speaker cable (16 gauge or

thicker) to connect the positive outputs of the

M•800 to the speaker’s positive inputs, and the

negative outputs to the speaker’s negative in-

puts. You probably know the importance of

getting these connections correct — if one

side is hooked up “out of phase,” this will cause

a reduction in the bass output and your pay.

If you’re using the M•800 in

BRIDGE

mode,

the speaker connects across the red posts only

(see page 16 for details).

In addition to the binding posts, the M•800

has 1/4" TS (tip-sleeve ) outputs, so you can use

speaker cables with 1/4" TS plugs. The tip is

positive (+) and the sleeve is negative (–).

They’re wired in parallel with the binding posts

and behave exactly the same (except they can’t

be used in

BRIDGE

mode).

You can use both the 1/4" jacks and the

binding posts simultaneously. Just remember

that doing so creates two parallel loads.

Be Aware: Should you

choose to terminate your

speaker cables with 1/4"

TS plugs, make sure no-

body confuses these

cables with line-level

cables, (i.e., guitar cords). Guitar cords are

not designed to handle the high current out-

put of power amplifiers.

Furthermore, line-level inputs (like the sig-

nal input on a mixer) are not designed to

handle speaker-level voltages. The results are

not pretty, and can ruin a mixer technician’s

whole day.

CHANNEL

SPEAKER OUTPUTS

––

MONO

BRIDGE

BAL/UNBAL

MONO

BRIDGE

OFF ON OFF ON OFF ON

120 VAC 60 Hz

1500 WATTS

CONSTANT DIRECTIVITY

HORN EQ /AIR EQ

LOW CUT

FILTER

170 Hz

OFF

4.5k Hz

6k Hz

2k Hz

AIR EQ

100 Hz

STAGE

MONITOR

TYPICAL

35 Hz

TYPICAL

STEREO

(MONO BRIDGE)

800 WATTS

4 OHM LOAD MIN.

400 WATTS CH

2 OHMS LOAD MIN.

THRU

LOW CUT

FILTER

INPUT

THRU

170 Hz

OFF

4.5k Hz

6k Hz

2k Hz

AIR EQ

TYPICAL

35 Hz

CONSTANT DIRECTIVITY

HORN EQ /AIR EQ

CHANNEL

BAL/UNBAL

AMP MODE

LIMITER

SERIAL NUMBER

MANUFACTURING DATE

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION

AVIS:

RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR

THE FOLLOWING ARE TRADEMARKS/REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "FR SERIES", & THE "RUNNING MAN" FIGURE

CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC • WOODINVILLE

100 Hz

STAGE

MONITOR

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

Mackie M800 Bedienungsanleitung Seite 12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Empfänger und Verstärker Mackie M800