Mackie J1400 Technical Information

10Rear Panel Features2. POWER SWITCHPress the top of this rocker switch to turn on the mixer. The front panel power LED (22) will glow with happiness

113. SPEAKER-LEVEL OUTPUTSThese output connections provide speaker-level output power from the internal power amplifi ers to your passive speakers. The

1415161718202119567 8 86 6 6 6 65 5 5 5 5 5 5 5 59101112222324252629303334272831133273512Front Panel FeaturesMicrophone-level signals are passed throu

13The mixer's phantom power is globally controlled by the phantom (23) switch on the front panel. (Phantom power for all mics is turned on and o

1412. POWER AMP MODE SWITCHThis two-position switch lets you choose which signal paths from the mixer section are sent to the internal power amplifi er

15Channel ControlsThe 10 vertical channel strips look very similar, with only a few differences between them. Each channel works independently, and co

16CHANNEL EQUALIZATION (EQ)Each channel has 3-band equalization: low shelving, mid peaking, and high shelving. It’s probably all the EQ you’ll ever ne

1717. AUX SEND MONThis control allows you set up a nice monitor mix, independent of the main mix. Adjust these controls on each channel until your ban

18Master Controls22. POWER LEDThis LED comes on when the powered mixer is plugged into the correct-voltage AC mains supply, and the rear panel power s

19rather than boost the wanted range. You can reduce the level of some frequency bands where feedback occurs.26. MAIN MIX METERSDeveloped from a harml

2SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this

2032. MONITOR MASTER LEVELThis knob controls the overall level of the monitor mix, and affects the monitor meter (30), monitor send line-level output

No. TitleDescription Example of its use1 ROOM 1This room has a bright tone with lots of scattered refl ections to simulate harder, more refl ective surf

22Appendix A: Service InformationIf you think your TAPCO powered mixer has a problem, please check out the following troubleshooting tips and do your

23Appendix B: Connections“XLR” ConnectorsTAPCO mixers use 3-pin female “XLR” connectors on all microphone inputs, with pin 1 wired to the grounded (ea

24Appendix C: Technical InformationDistortion (THD + N)(1 kHz, A-Weighted )Mic mono: <0.008% low gainLine mono: <0.008% low gainLine stere

11.67 in/ 296.4 mm18.44 in/ 468.4 mm11.30 in/ 287 mmWEIGHT22 lb 10 kgDimensions25Correct Disposal of this product: This symbol indicates that this pro

Block Diagram2648VMICS LRLRMAINLEVELLRMONOCHANNELSSTEREOCHANNELSMICLINEGAINLEVELLEVELMONLEFTMAIN OUTRIGHTMAIN OUTMONITORSENDAMP A INPUTAMP MODEAMP B I

27TAPCO LIMITED WARRANTYA. LOUD Technologies Inc. warrants all materials, workmanship and proper operation of this product for a period of one year

Part No. SW0696 Rev. B 08/08©2006-2008 LOUD Technologies Inc. All Rights Reserved.3What me, read a manual?Your new TAPCO® powered mixer is designed

4Getting StartedWe realize that you must be really keen to try out your new powered mixer, but please read the safety instructions on page 2, and this

5• Two internal power amplifi ers, each rated at 500 watts peak into 4 ohms• Two selectable amplifi er modes (stereo mains, mono-main/monitor) • 10 ch

MicrophonesKeyboard6915 Passive Speakers(plays stereo main mix)TAPCO J-2500Power AmplifierTAPCO Thump-15A Powered Speakersused as Stage MonitorsRecord

MicrophonesKeyboard 1CD/DVDPlayer6912 Passive Speakers6912 Passive SpeakersTAPCO J-2500Power AmplifierStage MonitorsThump TH-15APowered Speakersin Ove

Drum Kit MicsVocalMicrophones6912 Passive Speakers(plays mono main mix)Amp Modeswitch set toMain/MonBassGuitarElectricGuitarDI BoxGuitarProcessorThump

Drum Kit Mics6912 Passive Speakers(play stereo main mix)TAPCO J-2500Power AmplifierStage MonitorsAmp Modeswitch set toStereo MainAcoustic Guitarand Mi